Torch-On Roofing Vancouver | Two-Ply SBS Flat Roofs | Stonnex
Free Inspection Call Now
WhatsApp
Torch-On Roofing · Two-Ply SBS

Two-Ply SBS Torch-On:
the Flat Roof Built for the Wet Coast

Fully torched IKO base and cap sheets, proper slope to new drains, and a written warranty. Residential, strata and commercial.

Book Your Free Roof Inspection — Takes 30 Seconds
No obligation  ·  Respond within one business day  ·  Or call 604-935-6976
WorkSafeBC RegisteredClearance verifiable online
$5M Liability InsuranceCertificate on request
BC IncorporatedWorkSafeBC registered
500+ Completed RoofsLower Mainland & Fraser Valley

Two-Ply SBS Torch-On:
The Flat Roof Built for the Wet Coast

Torch-on is the default flat and low-slope roof in the Lower Mainland for a reason. Two layers of SBS-modified bitumen, heat-welded to each other and to the deck, with nothing mechanically fastened through the waterproofing layer, give a monolithic membrane that handles 1,200 millimetres of annual rain, standing water at a slow drain, and the freeze-thaw cycles of a coastal winter.

Stonnex installs IKO two-ply systems on residential flat roofs, garage and carport roofs, sundecks over living space, and commercial buildings. Every torch-on roof carries a written 5-year Stonnex labour warranty and the manufacturer's material warranty.

  • IKO TP-180 FF base sheet, fully torched; TP-250 granulated cap sheet, fully torched
  • Protecto board or recovery board over existing decks where required
  • Tapered EPS insulation to correct ponding and build slope to drains
  • New drains, scuppers, overflow outlets and 26-gauge metal flashings
  • Residential, strata and commercial; full tear-off or overlay where the deck allows
Two-ply torch-on flat roof installation, commercial building, Lower Mainland

How a Two-Ply Torch-On Roof Is Built

  1. Deck. Existing roofing is removed to the deck, or where the deck and insulation are sound, a recovery board is mechanically fastened over the old roof. Rotten sheathing is replaced. On commercial decks an IKO 1/8-inch protecto board is mechanically fastened as the substrate.
  2. Slope and drains. Flat roofs are never flat; they need a minimum 2 percent slope to a drain. Where the existing roof ponds, tapered EPS insulation builds the slope. New drains, 3-inch scuppers and overflow outlets go in before the membrane.
  3. Base sheet. IKO TP-180 FF, a fibreglass-reinforced SBS base sheet, is torched to the substrate across its full surface. Full torching, not spot adhesion, is what stops wind uplift and water migration under the membrane.
  4. Details first. Drains, stacks, curbs and walls get membrane flashings before the cap sheet, so every detail sits under the finished layer rather than patched on top of it.
  5. Cap sheet. IKO TP-250, a heavier granulated SBS cap sheet, is torched to the base across its full surface with 3-inch side laps and 6-inch end laps bled out to a visible bitumen line. Granules protect the bitumen from UV and give the finished roof its colour.
  6. Metal and finish. 26-gauge metal edge, cap and counter flashings, MS-Detail with granules at seams and terminations, and vents sized for the roof area.

Why Torch-On Suits Our Climate

Environment Canada's 1991 to 2020 climate normals put Vancouver International Airport at about 1,190 millimetres of precipitation a year, Abbotsford closer to 1,540, and the North Shore mountains far higher. More than three quarters of it falls between October and April, often in multi-day events where a flat roof holds water against every seam for hours. Fully adhered SBS has no seams a fastener passes through and no edges that can lift and let water in: a heat-welded lap is as strong as the sheet itself.

SBS also stays flexible well below freezing, so the membrane tolerates the expansion and contraction of a cold snap after a wet week without cracking. That combination, flexibility and fully adhered redundancy, is why torch-on remains the standard here where single-ply systems dominate drier markets.

Torch-On Against the Alternatives

SystemStrengthsLimitsTypical life, Lower Mainland
Two-ply SBS torch-onFully adhered, redundant layers, repairable by torching in a patch, proven here for 40 yearsOpen flame installation needs a trained crew and fire-watch; heavier than single-ply20 to 30 years
TPO / PVC single-plyLighter, reflective, fast to install on large simple roofsSingle layer, heat-welded seams only as good as the installer, less common locally so fewer repair crews15 to 25 years
EPDM rubberLow cost, flexibleGlued seams are the weak point in standing water; limited residential use here15 to 20 years
Tar and gravel (BUR)Historically durableHeavy, hard to inspect and repair, few crews still install itLegacy only

Sundecks and Living Space Below

A torch-on roof under a walking deck is the most demanding residential application there is: foot traffic, planters, furniture and a living room underneath. Stonnex builds these as a two-ply system with a fast-and-stick base over separation framing and a 250 cap sheet, with duckboard or pavers on pedestals above so nothing sits directly on the membrane and water drains freely beneath.

Cost

Residential two-ply torch-on runs $7.00 to $12.00 per square foot installed before GST, or typically $7,000 to $14,000 for a detached home's flat section. Commercial tear-offs with new drains, insulation and metal are quoted individually. Full details are in the roof replacement cost guide. For strata and commercial buildings see strata roofing, and for low-slope systems generally see flat roofing.

Common Questions

Torch-On
FAQs

What is torch-on roofing?
Torch-on is a flat-roof system made of SBS-modified bitumen sheets that are heat-welded to the deck and to each other with a propane torch. Stonnex installs a two-ply system: an IKO TP-180 base sheet and a TP-250 granulated cap sheet, both fully torched, so the finished roof is one continuous bonded membrane.
What does SBS mean?
Styrene-butadiene-styrene, a synthetic rubber blended into asphalt. It keeps the membrane flexible in cold weather and lets it stretch and recover with building movement, which is why SBS torch-on outlasts plain asphalt systems in a freeze-thaw coastal climate.
How long does a torch-on roof last in Vancouver?
A properly installed and drained two-ply SBS roof lasts 20 to 30 years here. Drainage decides most of that range: a roof that ponds ages faster than one that clears within 48 hours of rain, which is why Stonnex corrects slope with tapered insulation where needed.
Why is torch-on the standard in the Lower Mainland instead of TPO?
Our rainfall and multi-day wet events favour a fully adhered, two-layer system with no fasteners through the waterproofing and no reliance on a single seam. Torch-on has four decades of local track record and every roofing crew here knows how to repair it. TPO suits large, simple, drier roofs; it is less common and less proven in this climate.
Can torch-on be installed in the rain?
No. The deck and base sheet must be dry for the bitumen to bond. We schedule torch-on for dry windows and keep the roof watertight overnight between phases. Emergency patches can be applied in light rain and permanently redone when dry.
Does a torch-on roof need maintenance?
Very little, but not none. Keep drains and scuppers clear each fall, keep foot traffic off the membrane or on pavers, and have it inspected after 10 years. Granule loss on the cap sheet or any soft spots are the early signals; both are repairable by torching in new membrane.
What warranty comes with torch-on?
A written 5-year Stonnex labour warranty, plus IKO's material warranty registered in your name. The shorter labour term versus our 10-year shingle and metal warranty reflects the harsher duty a flat roof sees, and it is the same term most reputable flat-roof installers in BC offer.
Is torch-on safe with an open flame?
Installed by a trained crew with fire-watch procedures, yes. Stonnex crews torch to manufacturer specification, keep extinguishers on the roof, use torch-safe techniques at walls and wood details, and complete a post-installation fire watch before leaving site.

Ready to Get Started?

Free inspection, no obligation. We respond within one business day.

Book Free Inspection 604-935-6976
What Homeowners Say

Trusted by Hundreds of
Lower Mainland Families

★★★★★

"Professional from the first call to final cleanup. The crew was respectful of our property and the workmanship is outstanding. Highly recommend Stonnex."

Michael T. — North Vancouver
★★★★★

"They gave us an honest assessment and a fair price. The roof looks beautiful and we felt informed at every step. This is how every contractor should operate."

Sarah K. — Burnaby
★★★★★

"Quick response, quality work, and they cleaned up completely after. We had quotes from three companies and Stonnex was the clear choice."

David L. — Langley
Where We Work

Serving the
Lower Mainland

We serve homeowners throughout Metro Vancouver and the Fraser Valley. Click your city for local reroofing information and pricing.

Vancouver Surrey Burnaby North Vancouver Coquitlam Langley Richmond Abbotsford
More Services

Other Ways
We Can Help